Packetmaster 30 Gbit Appliance

The CUBRO Packetmaster combines up to 24 x 10/100/1000 ports and 2 x 10Gbit ports with the most powerful network process engine available on the market. This unit can handle up to 30Gbit IP Traffic per second. Basically the Packetmaster is a Test Access Port (TAP) but can do a lot more and is a high performance multipurpose IP traffic handling engine. It can also be used as router, switch, cross connect, aggregator, filter, load balancer ..

Link/Port Aggregation
Aggregation of up to 24 Ports or 12 links to a single or multiple output ports.

Filter
Filters traffic by IP address, port number and physical input port.

Load balancing
Load balances traffic by IP address, port number and physical input port.

Duplicated traffic remover
This function fully automatically removes duplicated packets. This function is extremely important when monitoring multiple links and entities where the same traffic is usually captured more than once.

10G traffic demultiplexer
If highly loaded 10G links have to be monitored the traffic can be easily demultiplexed into 24 low traffic Gbit links.

Flexible unit combination
Various units can be connected together – e.g. 240 input ports monitored at 24 output ports is straight forward and easy.

Cross connect function
Packetmaster can work as layer 3 cross connect plus aggregator and filter.

Jumbo Frame Support
The Packetmaster supports jumbo Ethernet frames with a size of up to 9000 Bytes – this feature is supported in all applications

Modular software concept and easy upgrade capabilties
Because of its open hardware and its flexible and modular software concept the Packetmaster can grow with customers requirements.

SFP and XFP Modules
For a maximum of flexibility the Packetmaster is designed to run with any kind of SFP and XFP

Rugged 19” Housing
The Packetmaster is delivered in a ruggedized 19” 1U housing with precise connector labeling on the front panel.

Different Power Versions
48 VDC or 230 VAC in dual and single power supply versions available.

Management
Management is possible over RS232 and Ethernet. Moreover a special option for in-band management is also available.

Easy use and operation
For straight-forward operation and supervision the Packetmaster supports SNMP and CLI.

Packetmaster 2

Link/Port Aggregation
Aggregation of up to 34 ports or 16 links to a single or multiple output ports.

Filter
Filters traffic by IP address, port number and physical input port. As advanced option we offer the unique payload filtering „fingerprint filter“

Load balancing
Load balances traffic by IP address, port number and physical input port.

Duplicated traffic remover
This function fully automatically removes duplicated packets. This function is extremely important when monitoring multiple links and entities where the same traffic is usually captured more than once.

10G traffic demultiplexer
If highly loaded 10Gbit links have to be monitored the traffic can be easily demultiplexed into 24 low traffic Gbit links.

Flexible unit combination
Various units can be connected together – e.g. 240 input ports monitored at 24 output ports is straight forward and easy.

Cross connect function
Packetmaster can work as layer 3 cross connect plus aggregator and filter.

Jumbo Frame Support
The Packetmaster supports jumbo Ethernet frames with a size of up to 9000 Bytes – this feature is supported in all applications

Modular software concept and easy upgrade capabilties
Because of its open hardware and its flexible and modular software concept the Packetmaster can grow with customers requirements.

SFP and SFP+ Modules
For a maximum of flexibility the Packetmaster is designed to run with any kind of SFP and SFP+

Rugged 19” Housing
The Packetmaster is delivered in a ruggedized 19” 1U housing with precise connector labeling on the front panel.

Different Power Versions
48 VDC or 230 VAC in dual and single power supply versions available.

Management
Management is possible over RS232 and Ethernet. Moreover a special option for in-band management is also available.

Easy use and operation
For straight-forward operation and supervision the Packetmaster supports SNMP and CLI.

Packetmaster EX48

The Packetmaster EX product series has been developed to preaggregate low and medium loaded 10G links to save ports on expensive 10G traffic Analyzers and Capture tools. Alternatively the appliances can be used to automatically switch heavily loaded 10G links between different Analyser- and/or Capture ports.

Once wired, any tool connected to the Packetmaster EX can access any datalink tapped or spanned into the appliance. An intuitive, very easy to use Command Line Interface allows connecting ports to each other in seconds. Changing the setup of the appliance does not influence ports not being part of the change. Each port automatically becomes a 1G or 10G port depending on the SFP(+) used.

PDF Datasheet

Copper TAP 10/100

Product Features:

• 100% Throughput , very low delay
  and fully transparent
  
• LINKSAVE Function
  
• LED Indicators
  
• Different Power Versions
  
• Different Cabinet versions available
  
• Easy use and operation

Copper TAP 100M Dual

PDF Datasheet

This special version has two output ports per direction . Available as 19“ version with two independent units or in an half 19“ version.

Product Features:

• 100% Throughput , very low delay
  and fully transparent
• LINKSAVE Function
• LED Indicators
• Different Power Versions
• Remote Management Interface
• Easy use and operation

Copper TAP 1000B-T

Product Features:

• 100% Throughput , very low delay
  and fully transparent
• Protects your network links
• Number of Monitoring Ports
• LED Indicators
• Different Power Versions
• Remote Management Interface
• Easy to use and operate

Copper TAP 1000B-T

PDF Datasheet

Ethernet Appliance up to 10G

Product Features:

• Filter Application (duplication)
• Counting Application
• Drop Application

2 Channel Full Duplex Ethernet TAP

Product Features:

• Active TAP based on store-and-forward architecture
• Network ports:
  Two pairs of one 10/100/1000Mbps RJ-45 and Mini-GBIC combo ports for traffic up to 2 network segments Auto network sensing and negotiating of speed
• Monitoring port:
  One 10/100/1000Mbps RJ-45 and Mini-GBIC combo ports
  Auto MDI/MDI-X and auto correction of twisted-pair polarity
• Management port:
  10/100Mbps RJ45 with 852 CPU module embedded
• Console port:
  One RS-232 port for real-time display of traffic statistics

Gbit Aggregation Engine

Product Features:

• Multilink Traffic Aggregation
• LED Indicators
• Different Power Versions
• Rugged 19” Housing
• Dual Monitor Output
• Easy use and operation

Gbit Multilink Aggregation TAP

Product Features:

• Multilink Traffic Aggregation
• LINKSAVE Function
• LED Indicators
• Different Power Versions
• Rugged 19” Housing
• Dual Monitor Output
• Easy use and operation

Gbit Multilink Aggregation TAP

PDF Datasheet

Multilink Aggregation TAP (RJ45)

Multilink Aggregation TAP (RJ45)

PDF Datasheet

Product Features:

• Multilink Traffic Aggregation
• LINKSAVE Function
• Link Extension
• Rugged 19” Housing
• LED Indicators
• Different Power Versions

Converter TAP mini

Converter TAP mini

PDF Datasheet

The CUBRO Converter TAP converts the traffic of an optical Gigabit Ethernet link to an SFP output. With its fully passive connection to the network it does not influence the traffic of the optical network link while still allowing full access to the traffic via the electrical 1000B-T monitoring port.

For all these cases CUBRO provides a cost-effective, flexible and small device which converts the incoming traffic to an additional output port. The CUBRO Converter TAP uses SFP modules which give a maximum off flexibility to the user. It is possible to change or add SFPs during operation without interrupting other ports. (hot-swap)

Moreover, it is possible to use non-vendor specific SM, MM, COPPER, CWDM, BIDI -SFP, in any combination.

The path from input to the output ports is fault-transparent. If the link on input port is going down, the output ports follow with a short delay.

The path from input to the output ports is layer 1 to 7 transparent. Any error on the input port will be copied to all output ports.

Product Features:

• single / multimode output via SFP+
• Carrier Grade Design
• splitting ratio 80:20 on SM 50:50 on MM
• linksave full passiv on monitoring link

Functions:

• Port Multiplication
  • One input Port will be converted to one SFP Port.
    
• Multiple output SFP supported
  • Copper Gbit , SM, MM BIDI
• Fault Propagation
  • If the link on the input port is going down the output ports will follow with a short delay.
• LED IndicatorsL
  • LEDs on the front panel indicates power and signal status.
• Power
  • 12V DC Supply,power dissipation : 6 W
• Propagation Delay (In to Out)
  • 0.7 ns only
• Physical Dimensions (H x W x D)
  • 3 x 11,2 x 17 cm 1,8 x 4,4 x 6,7 in
• Rugged Housing
  • Stable Aluminium Housing with precise connector labelling on front panel.
• 19" Rack mountkit also avaiable

GE Converter TAP

GE Converter TAP

PDF Datasheet

Multilink PORT duplication TAP

Multilink PORT duplication TAP

PDF Datasheet

Product Features:

• Multilink Traffic Duplication
• LED Indicators
• Power Versions
• 4 Port Version avaliable on request
• Rugged 19” Housing
• Easy use and operation